avrdude: Version 6.1-20140313, compiled on Apr 17 2014 at 14:10:00 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "avrdude.conf" User configuration file is "/home/raim/.avrduderc" User configuration file does not exist or is not a regular file, skipping Using Port : usb Using Programmer : xplainedmini avrdude: usbdev_open(): Found mEDBG CMSIS-DAP, serno: ATML2222040200000573 avrdude: usbdev_open(): WARNING: failed to set configuration 1: Device or resource busy avrdude: Found CMSIS-DAP compliant device, using EDBG protocol AVR Part : ATmega168P Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PC2 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 20 4 0 no 512 4 0 3600 3600 0xff 0xff flash 65 6 128 0 yes 16384 128 128 4500 4500 0xff 0xff lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : JTAGICE3_DW Description : Atmel AVR XplainedMini in debugWire mode ICE hardware version: 0 ICE firmware version: 1.00 (rel. 0) Serial number : ATML22220402000005730573 Vtarget : 5.00 V JTAG clock megaAVR/program: 0 kHz JTAG clock megaAVR/debug: 0 kHz JTAG clock Xmega: 0 kHz PDI clock Xmega : 0 kHz avrdude: JTAG ID returned: 0x0b 0x94 0x00 0x00 avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.01s avrdude: Device signature = 0x1e940b avrdude: safemode: Fuse reading not support by programmer. Safemode disabled. avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: Chip erase not supported in debugWire mode avrdude: reading input file "test1.hex" avrdude: input file test1.hex auto detected as Intel Hex avrdude: writing flash (138 bytes): Writing | avrdude: jtag3_edbg_send(): Fragmentation not (yet) implemented! avrdude: jtag3_edbg_recv(): Unexpected response 0x81, 0x00 avrdude: write memory command: timeout/error communicating with programmer (status -1) ######################### ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; # ***failed; avrdude: Error: JTAGICE3_DW programmer uses avr_write_page() but does not provide a cmd() method. *** page 127 (addresses 0x0000 - 0x007f) failed to write ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; ***failed; # ***failed; ***failed; avrdude: Error: JTAGICE3_DW programmer uses avr_write_page() but does not provide a cmd() method. *** page 9 (addresses 0x000a - 0x0089) failed to write # | 100% 0.01s avrdude: 138 bytes of flash written avrdude: verifying flash memory against test1.hex: avrdude: load data flash data from input file test1.hex: avrdude: input file test1.hex auto detected as Intel Hex avrdude: input file test1.hex contains 138 bytes avrdude: reading on-chip flash data: Reading | avrdude: jtag3_edbg_recv(): Unexpected response 0x81, 0x13 avrdude: read memory command: timeout/error communicating with programmer (status -1) #########################avrdude: jtag3_edbg_recv(): Unexpected response 0x81, 0x23 avrdude: read memory command: timeout/error communicating with programmer (status -1) avr_read(): error reading address 0x0000 read operation not supported for memory "flash" avrdude: failed to read all of flash memory, rc=-2 avrdude: jtag3_edbg_recv(): Unexpected response 0x81, 0x33 avrdude: AVR sign-off command: timeout/error communicating with programmer (status -1) avrdude done. Thank you.