C:\workdir\vendor\projectProgrammer>avrdude -v -p m6490p -c jtag3 -U flash :w:combo.hex:i -U lfuse:w:0xE2:m -U hfuse:w:0xBA:m -U efuse:w:0xFB:m -U lock:w:0 xEF:m -U eeprom:w:eeprom.eep:a avrdude: Version 6.1, compiled on Mar 13 2014 at 00:09:49 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "C:\workdir\vendor\projectProgr ammer\avrdude.conf" Using Port : usb Using Programmer : jtag3 avrdude: usbdev_open(): did not find any USB device "usb" (0x03eb:0x2110) avrdude: usbdev_open(): Found JTAGICE3 CMSIS-DAP, serno: J30200014733 avrdude: Found CMSIS-DAP compliant device, using EDBG protocol AVR Part : ATmega6490p Chip Erase delay : 9000 us PAGEL : P00 BS2 : P00 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW Max W ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- --- -- --------- eeprom 65 20 8 0 no 2048 8 0 9000 90 00 0xff 0xff flash 65 6 256 0 yes 65536 256 256 4500 45 00 0xff 0xff lfuse 0 0 0 0 no 1 0 0 4500 45 00 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 4500 45 00 0x00 0x00 efuse 0 0 0 0 no 1 0 0 4500 45 00 0x00 0x00 lock 0 0 0 0 no 1 0 0 4500 45 00 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 Programmer Type : JTAGICE3 Description : Atmel AVR JTAGICE3 in JTAG mode ICE hardware version: 2 ICE firmware version: 3.08 (rel. 22) Serial number : J302000147334733↕▬‼♠¶♠U▼‗¤Fò±└▬▬↨♠↑♠Ö▼±¤åòq♣òÞö╗'f'w' ╦☺ùòè¶Åò°ö ¤xxxxxxx Vtarget : 3.25 V JTAG clock megaAVR/program: 32 kHz JTAG clock megaAVR/debug: 1012 kHz JTAG clock Xmega: 1000 kHz PDI clock Xmega : 1000 kHz avrdude: JTAG ID returned: 0x3f 0xc0 0x60 0x19 avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.09s avrdude: Device signature = 0x1e960c avrdude: safemode: lfuse reads as E2 avrdude: safemode: hfuse reads as BA avrdude: safemode: efuse reads as FB avrdude: NOTE: "flash" memory has been specified, an erase cycle will be perform ed To disable this feature, specify the -D option. avrdude: erasing chip avrdude: reading input file "combo.hex" avrdude: writing flash (65128 bytes): Writing | ################################################## | 100% 2.73s avrdude: 65128 bytes of flash written avrdude: verifying flash memory against combo.hex: avrdude: load data flash data from input file combo.hex: avrdude: input file combo.hex contains 65128 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 1.74s avrdude: verifying ... avrdude: 65128 bytes of flash verified avrdude: reading input file "0xE2" avrdude: writing lfuse (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of lfuse written avrdude: verifying lfuse memory against 0xE2: avrdude: load data lfuse data from input file 0xE2: avrdude: input file 0xE2 contains 1 bytes avrdude: reading on-chip lfuse data: Reading | ################################################## | 100% 0.01s avrdude: verifying ... avrdude: 1 bytes of lfuse verified avrdude: reading input file "0xBA" avrdude: writing hfuse (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of hfuse written avrdude: verifying hfuse memory against 0xBA: avrdude: load data hfuse data from input file 0xBA: avrdude: input file 0xBA contains 1 bytes avrdude: reading on-chip hfuse data: Reading | ################################################## | 100% 0.01s avrdude: verifying ... avrdude: 1 bytes of hfuse verified avrdude: reading input file "0xFB" avrdude: writing efuse (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of efuse written avrdude: verifying efuse memory against 0xFB: avrdude: load data efuse data from input file 0xFB: avrdude: input file 0xFB contains 1 bytes avrdude: reading on-chip efuse data: Reading | ################################################## | 100% 0.01s avrdude: verifying ... avrdude: 1 bytes of efuse verified avrdude: reading input file "0xEF" avrdude: writing lock (1 bytes): Writing | ################################################## | 100% 0.01s avrdude: 1 bytes of lock written avrdude: verifying lock memory against 0xEF: avrdude: load data lock data from input file 0xEF: avrdude: input file 0xEF contains 1 bytes avrdude: reading on-chip lock data: Reading | ################################################## | 100% 0.01s avrdude: verifying ... avrdude: 1 bytes of lock verified avrdude: reading input file "eeprom.eep" avrdude: input file eeprom.eep auto detected as raw binary avrdude: writing eeprom (2048 bytes): Writing | ################################################## | 100% 1.39s avrdude: 2048 bytes of eeprom written avrdude: verifying eeprom memory against eeprom.eep: avrdude: load data eeprom data from input file eeprom.eep: avrdude: input file eeprom.eep auto detected as raw binary avrdude: input file eeprom.eep contains 2048 bytes avrdude: reading on-chip eeprom data: Reading | ################################################## | 100% 1.07s avrdude: verifying ... avrdude: 2048 bytes of eeprom verified avrdude: safemode: lfuse reads as E2 avrdude: safemode: hfuse reads as BA avrdude: safemode: efuse reads as FB avrdude: safemode: Fuses OK (E:FB, H:BA, L:E2) avrdude done. Thank you.