Wed 22 Jun 2011 03:00:28 AM UTC, original submission:
Field 194 seems consistent.
I tried to make some files transfert and the value was increasing. Then if left the drive inactive the value decrease.
I have two drives of that model and both acts the same way.
While compiling, the heat in the chassis rise, the temperature repported by both drives and a third already in the DB rise roughtly the same amount.
Here is and hddtemp --debug and a smartctl -a :
================= hddtemp 0.3-beta15 ==================
Model: ST3160815A
field(1) = 67
field(3) = 0
field(4) = 71
field(5) = 0
field(7) = 9
field(9) = 254
field(10) = 0
field(12) = 70
field(187) = 0
field(189) = 0
field(190) = 39
field(194) = 39
field(195) = 35
field(197) = 0
field(198) = 0
field(199) = 0
field(200) = 0
field(202) = 0
smartctl 5.41 2011-06-09 r3365 [i686-linux-2.6.39-gentoo-r1] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
START OF INFORMATION SECTION
Model Family: Seagate Barracuda 7200.10
Device Model: ST3160815A
Serial Number: 5RA9P3TN
Firmware Version: 3.AAD
User Capacity: 160,041,885,696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Jun 22 04:52:01 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
START OF READ SMART DATA SECTION
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 187714627
3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 71
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 137284753
9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 18686
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 70
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 055 045 Old_age Always - 39 (Min/Max 36/40)
194 Temperature_Celsius 0x0022 039 045 000 Old_age Always - 39 (0 22 0 0)
195 Hardware_ECC_Recovered 0x001a 077 075 000 Old_age Always - 48453435
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
|